Convivea
Forums => Computers - Technology => Topic started by: texasboy on July 06, 2006, 08:04:34 am
-
Just installed a new 3.0ghz HT Intel processor. The old chip was a budget one and not doing the job.
If it is any help to others dont apply the thermal paste like a peanut butter sandwich between the processor and the heatsink/fan. I used quite a lot of paste and wondered why the CPU temperatures were a little high 55-60 degrees C.
Scraped and smoothed a little ,ie just a thin film to allow good contact between components and temperature dropped back to the 44-48 degree mark.
Hope this helps
cheers
-
...mmm peanut butter. lol
TheHalf™
-
I have to say I love AMD for this one, with Copper Paste already on my heatsinc my CPU stays at 30 - 33 degrees C :)
-
Did a re-clean and applied minute ammount of paste. What a difference.
Running at 32C cpu fan at 1080rpm.
Copper heatsinks are an excellent way of drawing heat from cpu but not so great at disapating. Manufacturers have learned that by mixing copper with alluminium they can get the best of both worlds. Copper heatsinks tend to be very overweight and more expensive.
With todays higher powered mo-bos and graphics it is not unusual for cpu temps to reach into the 50`s.It may be fair to say that if your temperatures stay in the low 30`s under programme load, then your system is is basically stock and not being put under any pressure.
Todays modern cpu is very unlike its predessors and can withstand temperatures that were unheard of a few years ago. You only have to read the forums to see that some cpu`s are quite happy and stable running at 60deg
cheers
-
Even when my CPU is under pressure it doesn't climb very high at all (and being a mathematician I run programs which push CPUs as far as they can go). I have to actually turn my CPU fan off to ever see it climb above 40.
-
Did a re-clean and applied minute ammount of paste. What a difference.
Running at 32C cpu fan at 1080rpm.
Copper heatsinks are an excellent way of drawing heat from cpu but not so great at disapating. Manufacturers have learned that by mixing copper with alluminium they can get the best of both worlds. Copper heatsinks tend to be very overweight and more expensive.
With todays higher powered mo-bos and graphics it is not unusual for cpu temps to reach into the 50`s.It may be fair to say that if your temperatures stay in the low 30`s under programme load, then your system is is basically stock and not being put under any pressure.
Todays modern cpu is very unlike its predessors and can withstand temperatures that were unheard of a few years ago. You only have to read the forums to see that some cpu`s are quite happy and stable running at 60deg
cheers
Tex... what the hell is your job? lol It just seems all of a sudden your far too knowledgeable about such things! :D
-
Did a re-clean and applied minute ammount of paste. What a difference.
Running at 32C cpu fan at 1080rpm.
Copper heatsinks are an excellent way of drawing heat from cpu but not so great at disapating. Manufacturers have learned that by mixing copper with alluminium they can get the best of both worlds. Copper heatsinks tend to be very overweight and more expensive.
With todays higher powered mo-bos and graphics it is not unusual for cpu temps to reach into the 50`s.It may be fair to say that if your temperatures stay in the low 30`s under programme load, then your system is is basically stock and not being put under any pressure.
Todays modern cpu is very unlike its predessors and can withstand temperatures that were unheard of a few years ago. You only have to read the forums to see that some cpu`s are quite happy and stable running at 60deg
cheers
Tex... what the hell is your job? lol It just seems all of a sudden your far too knowledgeable about such things! :D
Yea Tex...tell us dammit. lol ;D
-
Sorry folks.
I had thought that Billy had explained my new position.
I design circuit and tail components in a "sweetie mouse" factory. Our customers are sometimes confused and need advice on whether the tail should be analysed first or should they try to digest the whole product and hope for the best.
cheers
-
You what?
???
-
Sorry folks.
I had thought that Billy had explained my new position.
I design circuit and tail components in a "sweetie mouse" factory. Our customers are sometimes confused and need advice on whether the tail should be analysed first or should they try to digest the whole product and hope for the best.
cheers
Maybe you can fix the broken button on my logitech mouse.. :)
-
Maybe even Billy has forgotten>
For our younger viewers I will explain.
A Sweety Mouse was a very popular piece of candy . It has all the details of a proper mouse and was usually made out of marshmallow coated in fine sugar. Complete with tail/eyes/nose etc you were never quite sure where to take the first bite.lol
A bit sadistic when you pulled its head off.(no pun intended).
Sadly they dont seem to be on the market anymore.
Hope this helps ;D
cheers
-
Ah I see... makes sense.
Well... in a way... I never fully understood electrics, I can make a circuit, about it... :-[
-
I use water coolant.... so I don't have these problems
-kyopedlr
-
Hi guys! :)
So maybe it is the problem why my PC work slower than before. I just repaired my motherboard and I use a thermal paste and I applied alot on it. is it goes to your VGA card?
-
Hi guys! :)
So maybe it is the problem why my PC work slower than before. I just repaired my motherboard and I use a thermal paste and I applied alot on it. is it goes to your VGA card?
Hi Weera,
Normally we would apply thermal paste when installing a new CPU(processor) This would be between the heatsink fan and the back of the newly installed socket cpu. Normally a little dab, about the size of a pea is sufficient. As you may have read I applied quite a bit and things heated up etc. What you are basically looking for is a thin smear to transfer the heat to the heatsink fan. Make sure you have the heat sink securely fastened to the motherboard. Clean any of your cards(graphic or ram) before you install and you should be ok.
cheers
-
Hi guys! :)
So maybe it is the problem why my PC work slower than before. I just repaired my motherboard and I use a thermal paste and I applied alot on it. is it goes to your VGA card?
Hi Weera,
Normally we would apply thermal paste when installing a new CPU(processor) This would be between the heatsink fan and the back of the newly installed socket cpu. Normally a little dab, about the size of a pea is sufficient. As you may have read I applied quite a bit and things heated up etc. What you are basically looking for is a thin smear to transfer the heat to the heatsink fan. Make sure you have the heat sink securely fastened to the motherboard. Clean any of your cards(graphic or ram) before you install and you should be ok.
cheers
I got it Tex! Now I think I should clean it and apply the thermal paste just a bit. Or even a new heat sink fan will do..
Thanks alot. :)
-
Maybe even Billy has forgotten>
For our younger viewers I will explain.
A Sweety Mouse was a very popular piece of candy . It has all the details of a proper mouse and was usually made out of marshmallow coated in fine sugar. Complete with tail/eyes/nose etc you were never quite sure where to take the first bite.lol
A bit sadistic when you pulled its head off.(no pun intended).
Sadly they dont seem to be on the market anymore.
Hope this helps ;D
cheers
Don't listen to him guys, he's pullin yer pissers!!!
his actual job is to install and repair the machines that insert the tails into tampons.....hence the mouse, tails, etc....but, like you, i'm mystified by his new found tech knowledge.....l suspect that Tex has befriended a computer expert down the pub, and is plying him with drinks so he can pick his brains ;) :D
-
Now where did I see a smite button? Such language! 8)
cheers